Carbon Monoxide and Your HVAC System: What Every Riverside County Homeowner Must Know
Carbon monoxide is invisible, odorless, and deadly — and your furnace or heat pump could be the source. Learn the warning signs, what causes CO leaks, and how to keep your family safe.
Carbon monoxide (CO) is called the "silent killer" for good reason — you can't see it, smell it, or taste it. Yet every year, hundreds of Americans die from CO poisoning, and thousands more end up in emergency rooms. For homeowners in Riverside County, your HVAC system — specifically your furnace or heat pump — is one of the most common sources.
This guide covers everything you need to know to stay safe.
What Is Carbon Monoxide and Why Is It Dangerous?
Carbon monoxide is a byproduct of incomplete combustion. When fuel (natural gas, propane, oil) doesn't burn completely, it produces CO instead of harmless CO₂. At low concentrations, CO causes headaches, dizziness, and nausea. At high concentrations, it can be fatal within minutes.
The danger is that symptoms mimic the flu — many people don't realize they're being poisoned until it's too late.
How Your HVAC System Can Produce Carbon Monoxide
1. Cracked Heat Exchanger
The heat exchanger is the most common HVAC-related cause of CO leaks. It's a metal component inside your furnace that separates combustion gases from the air circulating through your home. Over time — especially in older systems — heat exchangers can crack.
When that happens, combustion gases (including CO) mix with your conditioned air and get distributed throughout your home through the ductwork.
Warning signs of a cracked heat exchanger:
- Soot or black marks around the furnace
- Excessive condensation on windows
- Furnace flame that flickers or appears yellow/orange instead of blue
- Unusual smells when the furnace runs
2. Blocked Flue or Exhaust Vent
Your furnace vents combustion gases outside through a flue pipe. If that pipe gets blocked — by a bird's nest, debris, ice, or corrosion — CO can back up into your home.
3. Improper Combustion
A furnace that isn't burning fuel efficiently produces more CO. This can happen due to:
- Dirty burners
- Incorrect gas pressure
- Insufficient combustion air (often caused by a clogged air filter or blocked vents)
4. Backdrafting
Backdrafting occurs when negative air pressure in your home pulls combustion gases back down the flue instead of letting them escape outside. This is more common in tightly sealed, energy-efficient homes.
Carbon Monoxide Detectors: Your First Line of Defense
Every home with a gas furnace, gas water heater, or attached garage should have CO detectors. Here's what you need to know:
Where to place them:
- On every level of your home
- Within 10 feet of each bedroom
- Near (but not directly next to) the furnace
- In the garage if it's attached to the house
What to look for in a detector:
- UL Listed certification
- Digital display showing CO levels (not just an alarm)
- Battery backup in case of power outages
- Replace every 5–7 years (they lose sensitivity over time)
Don't rely on one detector. CO can accumulate in one part of the house before spreading. Multiple detectors give you earlier warning.
Warning Signs Your HVAC System May Be Leaking CO
Even with detectors, it's worth knowing the physical warning signs:
- Headaches that improve when you leave home — classic CO poisoning symptom
- Multiple family members feeling ill at the same time — including pets
- Yellow or orange furnace flame — should always be blue
- Soot or black marks on or around the furnace
- Excessive condensation on windows when the furnace runs
- Furnace cycling on and off frequently (short cycling can indicate combustion problems)
What to Do If Your CO Detector Goes Off
- Get everyone out of the house immediately — don't stop to grab belongings
- Call 911 from outside or a neighbor's home
- Don't re-enter until emergency responders clear the building
- Call your HVAC company for an emergency inspection before using the furnace again
Annual Furnace Inspections: The Best Prevention
The single most effective way to prevent CO leaks from your HVAC system is an annual furnace tune-up before heating season. A qualified technician will:
- Inspect the heat exchanger for cracks
- Check the flue and exhaust vents for blockages
- Test combustion efficiency
- Clean burners and check gas pressure
- Verify proper airflow
In Riverside County, heating season typically starts in October. Schedule your furnace inspection in September to get ahead of the rush.
Revive Heating & Air Conditioning: CO Safety Inspections
At Revive, we take carbon monoxide safety seriously. Our furnace tune-ups include a thorough heat exchanger inspection and combustion analysis. If we find a problem, we'll explain your options clearly — whether that's a repair or, if the system is old and compromised, a replacement.
Don't wait until you smell something wrong (you won't). Call us to schedule your annual furnace inspection before heating season arrives.
Revive Heating & Air Conditioning Serving Riverside County, CA Call us: (951) 903-2077
Need help with your HVAC system? Revive Heating & Air Conditioning offers heating repair throughout Riverside County. Serving Menifee, Murrieta, and Temecula — call (951) 206-4975.
Explore Topics
Share this article
Written by
Revive Heating & Air Conditioning
Revive Heating & Air Conditioning is a family-owned HVAC company serving Riverside County, CA. Licensed (CSLB #1146947) and trusted by homeowners across Menifee, Temecula, Murrieta, and surrounding communities for AC repair, heating, installations, and maintenance.